|
|
Polymerization of Lactides in the Melt
Horkel, Ondřej ; Tomala, Libor (referee) ; Petrůj, Jaroslav (advisor)
This bachelor thesis deals with the problematics of Lactide polymerization in the melt. Theoretical part summarizes properties of lactic acid, lactides and polylactides as well as currently used methods of their preparation. In experimental part, a set of three experiments was designed, namely dependance of viscosity average molecular weight on catalyst concentration, polymerisation temperature and polymerisation time. This was achieved by measuring cinematic viscosity using Ubbelohde viscosimeter. As a result of these experiments, it was found that one of posssible combinations of conditions resulting in high molecular weight polymers is the following: concentration ratio of catalyst towards lactide 110–4, polymerisation teperature 160 °C and polymerisation time 3 hours.
|
|
|
Polylactide chemical recycling to Lactide
Kučerová, Eliška ; Pospíšilová, Aneta (referee) ; Figalla, Silvestr (advisor)
This diploma thesis deals with chemical recyclation polylactide to lactide. In the theory is summarized actual state of knowledge about chemical recyclation of polylactides, their properties, preparations a possibilities of characterization. Experimental part of work verify ethanolysis of PLA withthe samples of granulate, waste filaments and textiles. In the experimental work is suggested an optimalization of alcoholysis to direct yield of oligomer suitable for depolymerization to lactide. This method was verified for 5 different samples of PLA, which 4 of them was made of waste PLA. The time needed for depolymerization was evaluated and the effect of catalysis. Lactide and PLA recyclates was further analyzed by NMR, FTIR, DSC and GPC.
|
|
|
Determination of Hydroxyacids including their Low- and High Molecular Derivatives
Lysáková, Klára ; Mravcová, Ludmila (referee) ; Čáslavský, Josef (advisor)
This bachelor thesis deals with the determination of hydroxy acids and their low and high molecular polymers. The theoretical part deals with their properties, production and utilization. The polymers of these substances are used as biodegradable plastics and as absorbable sewing materials. The experimental part is focused on the determination of the total component and on the composition and amount of impurities of selected samples of ethyl lactate, lactides and polylactide. Analysis was performed by gas chromatography (GC) and tandem techniques using GC/MS and Head-Space-GC/MS analysis.
|
|
|
PLA Synthesis in Solution
Svítil, Jan ; Zdeněk, Přikryl (referee) ; Petrůj, Jaroslav (advisor)
This thesis is studying PLA syntheses using polymerization of lactides in solution. Theoretical part deals with properties and production of lactic acid, lactides and polylactides. In the experimental part, possibilities of lactides polymerization in solution has been summerised and verified. Syntheses were performed via “solvothermal” method using 7 solvents (toluene, chloroforme, 1,2-chlorobenzene, acetone, tetrahydrofurane, cyclohexane and hexane). Using hexane as solvent, at concentration ratio catalyzer/lactide 1 : 1 000, polymerization temperature 160 °C and reaction time 20 h, polylactide of viscosity average molecular weight 179 000 gmol–1 was synthetized from the lactide.
|
|
|
Biocomposite material for 3D print in the field of regenerative medicine
Chaloupková, Kateřina ; Obruča, Stanislav (referee) ; Přikryl, Radek (advisor)
The presented thesis deals with preparation of material for use in regenerative medicine based on poly(3-hydroxybutyrate) and its characterization. In addition to poly (3-hydroxybutyrate), there were used other materials lactic acid (PLA), tricalcium phosphate (TCP) and two types of plasticizers Citroflex®B-6 (CB6) and Syncroflex3114 (S3114). These materials were selected based on their biocompatibility and, in the case of TCP, also bioactivity. TCP allows new bone to grow on the surface of the scaffold. PLA was used to improve the mechanical properties of the material. Both plasticizers have been used to improve the processability of the material. Theoretical part of this work contains a literature review describing basic information about used materials. Aim of the experimental part is to prepare the material, characterization of properties and determination of printability on a 3D printer. The material is examined for thermal properties by thermogravimetric analysis and differential scanning calorimetry. This work also deals with the matter of 3D printing, especially FDM technology. It has been found that materials containing the syncroflex plasticizer are better processed and therefore printed on a 3D printer. The printability tests performed are temperature towers and filling studies. Printed samples were subjected to mechanical tests of tensile and bending tests. Experiments of cytotoxicity and biocompatibility of the material were also performed. Within the work, TCP particles were characterized using a particle size analyzer. The average TCP particle size is 10,76 µm. Using SEM-EDX, the distribution of TCP in sample filaments was subsequently observed, where it was found that by mixing TCP particles with the remaining components of materials, TCP particles agglomerate into formations up to 20 µm in size. Roughness of materials was determined by confocal microscopy. Cytotoxicity was also tested in the extracts of samples on mouse fibroblasts. Cytotoxicity was determined by metabolic activity assay and light microscopy. The metabolic activity test proved the biocompatibility of the observed materials; therefore, it was possible to perform cell proliferation and biocompatibility tests directly on the samples. Assays were performed using human mesenchymal stem cells. DNA quantification was used to determine cell proliferation. Shape of cells was subsequently observed by confocal microscopy. Tests confirmed growth of cells and their appropriate shape. Stem cell differentiation into bone was performed by measuring alkaline phosphatase activity.
|
|
|
New Processes of Lactid Acid Polymers Preparation
Figalla, Silvestr ; Svěrák, Tomáš (referee) ; Herink,, Tomáš (referee) ; Petrůj, Jaroslav (advisor)
The work focuses on new processes for the preparation of lactic acid derivatives. The main objective was to verify the feasibility of preparing high molecular weight polylactide using ethyl lactate as a precursor of lactide synthesis. Part of the work is devoted to the new ethyl lactate synthesis method. The experimental part of the thesis is divided into partial key steps on the way from the lactic acid to the high molecular polylactide. The preparation of anhydrous ethyl ester of lactic acid (EtLA) was solved in an innovative way using alcoholysis of the oligomeric lactic acid. A kinetic model for isothermal alcoholysis and equimolar reactants ratio was derived from this method. The ethyl lactate was oligomerized by transesterification into the low and high molecular weight oligomer with the help of newly found catalysts suitable for the reaction medium. Stannous lactate was used as catalyst for oligomerization of the low molecular weight polymer suitable for the preparation of lactide (Mn 1000 g.mol-1). Experimental polymerization of ethyl lactate into high molecular weight product in tens of kDa has been investigated with newly synthesized tetraethyllactoyl titanate, Ti(EtLA)4. The laboratory method was derived for the depolymerization of the oligomer into lactide. Optimal conditions found for lactidation are as follow: temperature 225 ° C, pressure 2 kPa, catalysis 0,05 mol% of stannous lactate (with respect to oligomer lactate units). The prepared lactide was refined to polymer grade purity by distillation and subsequent recrystallization from ethyl acetate and toluene. The method for the preparation of high molecular weight PLA through ROP polymerization of lactide has been optimized. By optimization, suitable catalyst concentration was found in combination with the polymerization temperature and the polymerization length. An equimolar mixture of Tin 2-ethylhexanoate and 1-decanol was used as the catalytic system. The optimal ROP conditions for achieving the maximum molecular weight and suppressed polymer coloration (yellowing) are: catalyst concentration 0,01 mol%, temperature 160 °C, and polymerization length 4 hours. PLA with molecular weight Mw= 447 ± 7,8 kg.mol-1 was prepared at these conditions and good repeatability of the result was achieved. The effect of naturally occurring lactide contaminants and their influence on the course and ROP result was experimentally verified on the optimized polymerization system. The purpose was to explore the effect of lactide contamination with water and ethanol as natural lactide contaminants. The results clearly confirm the orderly lower sensitivity of the polymerization system for the presence of ethanol as compared to water contamination. In the case of the presence of water, the course and the result of the polymerization in terms of both the conversion and achieved molecular weights are negatively affected, even when the water content is in the order of 0,001%. Conversely, the presence of ethanol has a positive effect on lactide conversion and polymer polydispersity. Lactides with an alcohol content of about one-tenth of a percent are suitable to reach molecular weights of PLA similar to commercially available products. This difference shoves a significant advantage in the proposed technology of preparing PLA from ethyl lactate, especially for easier purification of crude lactide into polymer grade purity.
|
|
|
Polylactide chemical recycling to Lactide
Kučerová, Eliška ; Pospíšilová, Aneta (referee) ; Figalla, Silvestr (advisor)
This diploma thesis deals with chemical recyclation polylactide to lactide. In the theory is summarized actual state of knowledge about chemical recyclation of polylactides, their properties, preparations a possibilities of characterization. Experimental part of work verify ethanolysis of PLA withthe samples of granulate, waste filaments and textiles. In the experimental work is suggested an optimalization of alcoholysis to direct yield of oligomer suitable for depolymerization to lactide. This method was verified for 5 different samples of PLA, which 4 of them was made of waste PLA. The time needed for depolymerization was evaluated and the effect of catalysis. Lactide and PLA recyclates was further analyzed by NMR, FTIR, DSC and GPC.
|
|
|
Biocomposite material for 3D print in the field of regenerative medicine
Chaloupková, Kateřina ; Obruča, Stanislav (referee) ; Přikryl, Radek (advisor)
The presented thesis deals with preparation of material for use in regenerative medicine based on poly(3-hydroxybutyrate) and its characterization. In addition to poly (3-hydroxybutyrate), there were used other materials lactic acid (PLA), tricalcium phosphate (TCP) and two types of plasticizers Citroflex®B-6 (CB6) and Syncroflex3114 (S3114). These materials were selected based on their biocompatibility and, in the case of TCP, also bioactivity. TCP allows new bone to grow on the surface of the scaffold. PLA was used to improve the mechanical properties of the material. Both plasticizers have been used to improve the processability of the material. Theoretical part of this work contains a literature review describing basic information about used materials. Aim of the experimental part is to prepare the material, characterization of properties and determination of printability on a 3D printer. The material is examined for thermal properties by thermogravimetric analysis and differential scanning calorimetry. This work also deals with the matter of 3D printing, especially FDM technology. It has been found that materials containing the syncroflex plasticizer are better processed and therefore printed on a 3D printer. The printability tests performed are temperature towers and filling studies. Printed samples were subjected to mechanical tests of tensile and bending tests. Experiments of cytotoxicity and biocompatibility of the material were also performed. Within the work, TCP particles were characterized using a particle size analyzer. The average TCP particle size is 10,76 µm. Using SEM-EDX, the distribution of TCP in sample filaments was subsequently observed, where it was found that by mixing TCP particles with the remaining components of materials, TCP particles agglomerate into formations up to 20 µm in size. Roughness of materials was determined by confocal microscopy. Cytotoxicity was also tested in the extracts of samples on mouse fibroblasts. Cytotoxicity was determined by metabolic activity assay and light microscopy. The metabolic activity test proved the biocompatibility of the observed materials; therefore, it was possible to perform cell proliferation and biocompatibility tests directly on the samples. Assays were performed using human mesenchymal stem cells. DNA quantification was used to determine cell proliferation. Shape of cells was subsequently observed by confocal microscopy. Tests confirmed growth of cells and their appropriate shape. Stem cell differentiation into bone was performed by measuring alkaline phosphatase activity.
|
|
|
New Processes of Lactid Acid Polymers Preparation
Figalla, Silvestr ; Svěrák, Tomáš (referee) ; Herink,, Tomáš (referee) ; Petrůj, Jaroslav (advisor)
The work focuses on new processes for the preparation of lactic acid derivatives. The main objective was to verify the feasibility of preparing high molecular weight polylactide using ethyl lactate as a precursor of lactide synthesis. Part of the work is devoted to the new ethyl lactate synthesis method. The experimental part of the thesis is divided into partial key steps on the way from the lactic acid to the high molecular polylactide. The preparation of anhydrous ethyl ester of lactic acid (EtLA) was solved in an innovative way using alcoholysis of the oligomeric lactic acid. A kinetic model for isothermal alcoholysis and equimolar reactants ratio was derived from this method. The ethyl lactate was oligomerized by transesterification into the low and high molecular weight oligomer with the help of newly found catalysts suitable for the reaction medium. Stannous lactate was used as catalyst for oligomerization of the low molecular weight polymer suitable for the preparation of lactide (Mn 1000 g.mol-1). Experimental polymerization of ethyl lactate into high molecular weight product in tens of kDa has been investigated with newly synthesized tetraethyllactoyl titanate, Ti(EtLA)4. The laboratory method was derived for the depolymerization of the oligomer into lactide. Optimal conditions found for lactidation are as follow: temperature 225 ° C, pressure 2 kPa, catalysis 0,05 mol% of stannous lactate (with respect to oligomer lactate units). The prepared lactide was refined to polymer grade purity by distillation and subsequent recrystallization from ethyl acetate and toluene. The method for the preparation of high molecular weight PLA through ROP polymerization of lactide has been optimized. By optimization, suitable catalyst concentration was found in combination with the polymerization temperature and the polymerization length. An equimolar mixture of Tin 2-ethylhexanoate and 1-decanol was used as the catalytic system. The optimal ROP conditions for achieving the maximum molecular weight and suppressed polymer coloration (yellowing) are: catalyst concentration 0,01 mol%, temperature 160 °C, and polymerization length 4 hours. PLA with molecular weight Mw= 447 ± 7,8 kg.mol-1 was prepared at these conditions and good repeatability of the result was achieved. The effect of naturally occurring lactide contaminants and their influence on the course and ROP result was experimentally verified on the optimized polymerization system. The purpose was to explore the effect of lactide contamination with water and ethanol as natural lactide contaminants. The results clearly confirm the orderly lower sensitivity of the polymerization system for the presence of ethanol as compared to water contamination. In the case of the presence of water, the course and the result of the polymerization in terms of both the conversion and achieved molecular weights are negatively affected, even when the water content is in the order of 0,001%. Conversely, the presence of ethanol has a positive effect on lactide conversion and polymer polydispersity. Lactides with an alcohol content of about one-tenth of a percent are suitable to reach molecular weights of PLA similar to commercially available products. This difference shoves a significant advantage in the proposed technology of preparing PLA from ethyl lactate, especially for easier purification of crude lactide into polymer grade purity.
|
|
|
Determination of Hydroxyacids including their Low- and High Molecular Derivatives
Lysáková, Klára ; Mravcová, Ludmila (referee) ; Čáslavský, Josef (advisor)
This bachelor thesis deals with the determination of hydroxy acids and their low and high molecular polymers. The theoretical part deals with their properties, production and utilization. The polymers of these substances are used as biodegradable plastics and as absorbable sewing materials. The experimental part is focused on the determination of the total component and on the composition and amount of impurities of selected samples of ethyl lactate, lactides and polylactide. Analysis was performed by gas chromatography (GC) and tandem techniques using GC/MS and Head-Space-GC/MS analysis.
|
guest ::
